Видео

I enjoyed your video, but that music made me want to kill something....

Man there must be something up with the tensioners with this model of ford's. Mine fucking exploded apart left my wife and kids stranded. I almost didn't catch it until I noticed it almost falling out when I went to check to see if the pulley itself would spin freely.

This was very informative and helpful. Thank you!

WHY WOULD THEY MAKE IT LIKE THIS???????????????????????

None of these videos or the shop manual show a gasket. Is there not one?

Is there a ground wire location ?

Not bad

plenum gasket is not covering the egr port!

I replaced both rear turn signal bulbs. However the backup bulbs are not working. The bulbs are good and the fuses are good. What could be the problem?

My rear turn signal bulb just went out on my 2003 Ford Focus ZX3 Hatchback. Thank you so very much for this instructional video!!

I have a 202 honda accord coupe vct engine and I need some help with where does the hors with the bracket hook up to.? I know one hose goes to the idaile control valve and the other end of the hose goes to the intake by the fuel injector but where does the bracket hook up to? Can someone please help

Was that coolant inside of the cylinders?

I've done this to multiple vehicles with gorilla glue and a penny or 2. why not make the switch mount to the metal on the pedal instead of adding a plastic adapter, like honestly.

Thx!!!! Using your video I fixed the issue all by myself!😁😁😁🎉 I’m such a big girl! 😂

Thank you for this video! 😊 This helped!

About to take this job on wish me luck

You shouldn’t took the intake off that’s extra work boss.

Really appreciate the video. Going to be a huge help. I'll be replacing radiator, fans, hoses (silicone), thermostat pump housing, thermostat, water pump, idler puller, belt tensioner, and accessory belt.....all as preventative maintenance

Where the throttle body connects on top there is 3 little tubes where line plug in can you tell what they are for?

Awesome vid thanks!

Never use a brick as a jack support block.😎

Thanks! We also never found a broken part. We just pushed the rotating plate & the handle worked again! So we sprayed WD4O in there & put it all back together. Maybe in cold weather it just gets stuck when it's old?

This is Part one right ?

Link to part!

wouldnt suggest using a jack in the dirt

For the Horde!

Try some WD 40 in the locking mechanism first

Not bad ⚡️

You couldve just removed the head and leace the intakemanifold exactly where it is

Very helpful thanks a bunch for your information it really hope me a lot keep up the good work

Can't do this with a manual can you? Even if in neutral?

👍Thanks Blake!

Thanks to your video I was able to fix the door handle on my 07 ford focus. Thanks so much for posting it.

You only have to drill if it's stuck in the off position. If it's in the on position then the release pin is lined up and if you stick something in that hole it will release the lock cylinder. When you drilled it in the on position you destroyed that release pin.

I don't normally reply to these videos as they do help. This video helped get the car started, but if you can't turn the key at all you can't unlock the steering wheel so, you can't drive the car if you can't turn the wheel. Is there a way to unlock the steering wheel??

I notice you took the timing belt off the dangerous way

Thank you. I'm about to do mine. I accidently loosened the radiator cap, lost water and the car really messed up.im a mechanic, but I always watch other's methods.

I just subscribed to your channel because I just recently bougt a 07 focus zx4 st and I'm having the same problem with the drivers door not opening. I got the door panel off and I can't tell if the handle is the problem or that big piece inside the door. It looks like a lot of work and I'm kind of intimidated by it. I guess I'll watch your video again and maybe I can figure it out

My question is...?! Why you need to remove the fuel line, I mean it's up it of the way in the video...... I don't understand

Hello, thanks for the video, tomorrow fix the Focus door with this information, good night Blake.

How did he get the door open 😅

It wasn’t that complicated last time I set it who do you think you are bullshiting?

Good looking out. And that friggen wingnut is definitely a pain in the ass.

Don’t weast your money

You’re missing the rubber bushings, it should be four

Good thing that you bought gloves.

Is this basically how I remove the cover of the cylinder to change my head gasket right ?

Absolutely brilliant video! I did most of the repair without taking too much apart, but I ran into the same issue with the hole not being aligned for an after market part. What I did though, was Drexel the metal on the outside edge, instead if making the hole bigger. Thanks for the vid!

Me agrada que pueda entenderlo, gracias a los subtítulos!! Excelente video! 😁👌

I just used this on my 2006 Pontiac Grand Prix. After chasing down the problem found out it was my Head gasket. Put it in August 3rd did it just like the instructions Said, day one was improvement, day two problem was completely fixed . Worked like they said. 100% satisfied